OrcaSlicer-bambulab/resources/profiles/Prusa/filament/Prusament PA-CF @CORE One.json

{
    "type": "filament",
    "name": "Prusament PA-CF @CORE One",
    "inherits": "fdm_filament_pa",
    "from": "system",
    "setting_id": "GFSA04",
    "filament_id": "Prusament PA-CF @CORE One",
    "instantiation": "true",
    "chamber_temperature": [
        "40"
    ],
    "close_fan_the_first_x_layers": [
        "4"
    ],
    "compatible_printers": [
        "Prusa CORE One 0.25 nozzle",
        "Prusa CORE One 0.3 nozzle",
        "Prusa CORE One 0.4 nozzle",
        "Prusa CORE One 0.5 nozzle",
        "Prusa CORE One HF 0.4 nozzle",
        "Prusa CORE One HF 0.5 nozzle"
    ],
    "fan_cooling_layer_time": [
        "15"
    ],
    "fan_max_speed": [
        "20"
    ],
    "fan_min_speed": [
        "15"
    ],
    "filament_cost": [
        "124.99"
    ],
    "filament_density": [
        "1.11"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_end_gcode": [
        "; Filament-specific end gcode"
    ],
    "filament_flow_ratio": [
        "1.05"
    ],
    "filament_max_volumetric_speed": [
        "6.5"
    ],
    "filament_minimal_purge_on_wipe_tower": [
        "35"
    ],
    "filament_notes": [
        ""
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_start_gcode": [
        "M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S45 ; set heatbreak target temp"
    ],
    "filament_type": [
        "PA"
    ],
    "filament_vendor": [
        "Prusa Polymers"
    ],
    "filament_z_hop": [
        "0.2"
    ],
    "hot_plate_temp": [
        "115"
    ],
    "hot_plate_temp_initial_layer": [
        "90"
    ],
    "idle_temperature": [
        "130"
    ],
    "nozzle_temperature": [
        "285"
    ],
    "nozzle_temperature_initial_layer": [
        "275"
    ],
    "overhang_fan_speed": [
        "20"
    ],
    "reduce_fan_stop_start_freq": [
        "0"
    ],
    "slow_down_layer_time": [
        "20"
    ],
    "slow_down_min_speed": [
        "15"
    ]
}